VPP10268
The TP-XD BLACKOUT is a one-sided, closable compact-sized tool pouch that holds a variety of tools, meters, fasteners and wire nuts. An inch (25mm) of depth has been added to increase the capacity and stability of the TP-XD BLACKOUT. The BLACKOUT edition features Veto Pro Pac’s proprietary V-SWAP™ system, enabling reconfiguring of the interior vertical pockets and/or the addition of other Veto pocket accessories. And, the zippered cover of the TP-XD BLACKOUT provides greater weather and dust protection for techs needing a compact bag for service calls requiring just the right amount of tools.
The TP-XD BLACKOUT comes with a Front Tool Panel, Tool Panel and 2 & 4 bit panels. You may purchase more of those panels if desired for an added cost below. There are additional panels, including front and rear Bulk Storage panels, and a Drill Panel, also sold separately and may be purchased below. Only one of the Tool Panel and Bulk Storage panel may be in the TP-XD BLACKOUT at a time, not both. Veto Pro Pac’s Padded Insert Box (sold separately below) may also be used with the TP-XD BLACKOUT.
Description
The TP-XD BLACKOUT is a one-sided, closable, compact-sized tool pouch featuring Veto Pro Pac’s proprietary V-SWAP™ system, enabling job specific customization. The larger capacity and zippered cover of the TP-XD BLACKOUT provide greater weather and dust protection for techs needing a compact bag for service calls requiring just the right amount of tools.
PRODUCT SPECIFICATIONS:
Height (H): 13.5" (34cm)
Width (W): 11" (28cm)
Depth: 8" (20cm)
Handle Height: 21in/53cm
Weight (empty): 6.5 lbs/3kg
Internal Volume: 435in3/7L
Max Payload: 30lbs/14kg
Tablet Pocket Dimensions:
Height: 10"
Width: 9"
MAXIMIZED TOOL STORAGE CAPACITY:
- V-SWAP™ removable tool pocket panel system; up to 24 internal pockets
- Tactical all-black construction
- 7 external tool pockets
- Backside tablet pocket
- Magnetic screw catcher
- “Hang-up” hook
- Over-molded rubber grip
- Padded shoulder strap
- YKK® zippers
- Deep base for stability
- Waterproof Polypropylene plastic base for moisture and abrasion protection
OTHER FEATURES:
Warranty: 5 Years (see Veto warranty terms and conditions)
Additional Information
VETO PRO PAC TOOL BAGS PRODUCT CARE AND MAINTENANCE
Keep the Zippers Clean & Lubricated
Over time, dirt and grit will “clog” the zipper coils preventing them from staying closed. To keep this from happening, clean and lubricate your zippers twice a year (more often if you work on a job site with a high amount of airborne debris). To clean the coils: Scrub them with soapy water; a tooth brush works very well. After scrubbing the coils, blow them out with an air hose to dislodge any other fine grit that didn’t dislodge with the brush. To lubricate the coils: Apply a silicone spray, beeswax or a zipper lubricant.
Protect the Zippers From Sharp Objects and/or Excessive Heat
Any sharp object or heat source is capable of permanently damaging the zippers. Once a zipper coil is cut or singed the zipper will not function and in most cases is not repairable. Most of the cut zipper coils we see are the result of sharp tools stored inside the bag with the sharp side facing up. Make sure to keep the sharp edges of your tools facing down in your bag and away from the zipper coils.
Don’t Overstuff the Bag
Overstuffing your tool bag will very likely cause significant stress on the zippers that is above and beyond what the bag was built for and will eventually cause the zipper(s) to separate. If you have to work hard to close your zipper(s), your tool bag is most likely overstuffed… proceed with caution!
DISCLAIMER : TOOLS ARE NOT INCLUDED!